N-3-(b)Redacted NSPI Response to UARB IR-12 (att 7-10) to IR-17
13 passages
(Cont'd) with a clearly visible rating plate, inscribed with the required standard information. - .3 Each and every device in the Protection, Control and Communication Panels shall be provided with a clearly visible identifying nameplate o...
AI summary The document outlines requirements for the installation of clearly visible and weatherproof nameplates on devices within Protection, Control, and Communication Panels. These nameplates must include specific information such as the manufacturer's name, type, serial number, voltage and current ratings, frequency rating, weight, date of manufacture, and CSA or cUL classification markings.
.10 Oil Temperature Gauges - .1 Operational Test - .1 Test each set point and reset point for all winding temperature gauges and record the results. - .2 Record discrepancies between the listed and actual winding temperature gauge settings.
AI summary The document outlines procedures for testing and recording the operational status of oil temperature gauges, specifically focusing on testing set and reset points and documenting discrepancies in winding temperature gauge settings.
.7 Current Transformers - .1 The manufacturer shall provide one (1) bushing transformer on each Recloser bushing, both load and line side. - .2 All bushing current transformers shall have 5A nominal secondary ratings. - .3 All bushing curr...
AI summary The document outlines specifications for current transformers, including requirements for secondary ratings, primary ratings, relaying accuracy, wiring, and connection ratios.
.5 Accessories - .1 Group-Operating Handle (Design "A", "B" and "D" only) - .1 The Contractor shall provide the all necessary operating handle provisions, including pipe, universal joints, bearings, and operator (lockable), such as to prov...
AI summary This section outlines the specifications for the group-operating handle, including requirements for its construction, installation, and compliance with standards. Key elements include grounding terminations, mounting arrangements, sealed bearings, and padlock provisions for safety.
.2 Ratings Nameplates - .1 The disconnect assembly shall be provided with an external nameplate secured next to the switch gang- operating handle containing the following information: - .1 Manufacturers Name - .2 Switch Type and Designatio...
AI summary The section outlines the requirements for the disconnect assembly's external nameplate, which must include specific information such as manufacturer name, voltage and current ratings, and applicable standards markings.
2.1 EQUIPMENT .1 General - IDENTIFICATION .1 Each and every device shall be provided with a clearly visible rating plate of weatherproof material, inscribed with the minimum information defined herein. - .2 Each and every device shall be p...
AI summary The document outlines specifications for equipment identification and material standards. It requires all devices to have visible rating and nameplates with specific details, and mandates that all materials used be of the highest quality and current manufacture.
2.3 FINISHES .1 Baked enamel finish: - .1 Conditioning of metal before painting: - .1 For corrosion resistance conversion coating to ASTM F1137. - .2 For paint base, conversion coating to ASTM F1137. - .2 Metal surfaces of luminaire housin...
AI summary This section outlines the requirements for the baked enamel finish on metal surfaces, including corrosion resistance standards, paint specifications, reflector finishes, and testing procedures for gloss, flexibility, and adhesion.
4.1 General - 4.1.1 Each and every device shall be provided with a clearly visible rating plate and identifying nameplate of weatherproof material, inscribed with the minimum information defined herein. - 4.2 Warning Signs - 4.2.1 All exte...
AI summary This section outlines requirements for rating plates and warning signs on electrical devices, including specifications for nameplates, safety signs, and information to be included on external nameplates as per CSA Standards.
1.14 Outdoor Finish - 1.14.1 The finish on painted metal parts shall be light gray, satisfying the requirements of ANSI Standard Z55.1 or No. 61 or No. 70; or Munsell 5.0 BG 7.0/0.4. Supplier shall supply one quart of touch-up paint per ci...
AI summary This section outlines specifications for the outdoor finish of electrical components, including paint standards, galvanization requirements, anticorrosion primers, and material finishes for various parts of the support structure and external hardware.
3.1 General 3.1.1 Each and every device shall be provided with a clearly visible rating plate of weatherproof material, inscribed with the minimum information defined herein, and legible for the life of the device.
AI summary This section outlines the requirement for each device to have a clearly visible, weatherproof rating plate containing essential information that remains legible throughout the device's lifespan.
ISO Standards - .1 ISO 9001 Quality Systems - 1.1.2 Unless otherwise noted, CSA Standards shall be given precedence when and where conflicts arise. - 1.1.3 The Pad Mounted Transformer assembly shall meet all applicable CSA requirements. If...
AI summary The document outlines requirements for ISO 9001 Quality Systems and specifies that CSA Standards take precedence in case of conflicts. It also details the need for compliance with CSA requirements for Pad Mounted Transformer assemblies and the acceptable inspection authorities under the Nova Scotia Electrical Installation and Inspection Act.
4 DOCUMENTATION 4.1 Manufacturers' Drawings - 4.1.1 The Pad Mounted Transformer assembly drawings submitted for review showing assembly, details, and layout showing anchor bolts, openings for cables, and all pertinent support structure loa...
AI summary This section outlines the requirements for manufacturers' drawings, specifically for Pad Mounted Transformer assemblies, including details on assembly, layout, anchor bolts, and component positioning.
Bedding and Edging - 2.1 Pavers, .1 Suppliers: approved by the ICPI. - .2 Concrete pavers: meet or exceed requirements set forth in CSA A231.2 and ASTM C140: - .1 minimum average cube compressive strength of 7250 psi (50 MPa). - .2 Resista...
AI summary The document outlines specifications for pavers and bedding materials, including compressive strength requirements, freeze-thaw resistance, pigment standards, and gradation criteria for manufactured sand used in bedding, referencing various standards from ASTM and CSA.