98234Complainant Submission - Nova Scotia Power Inc. Utility Service Requirements 2023 Edition - Effective May 1, 2023
30 passages
Added, changed or deleted text is indicated by bold italicized font. Clause Revision Action 1 Commercial driveway: Addition A commercial driveway is any temporary or permanent surface or accessway that is likely to be traveled by high side...
AI summary The text outlines additions and modifications to definitions and service entrance capacity regulations. It defines 'commercial driveway' and 'linked homes,' and revises the maximum single phase service entrance capacity under various conditions.
REFER TO CLAUSE 12.7 (D) OF THE UTILITY SERVICES REQUIREMENTS BOOK. SCALE NTS UNITS NOTED DRAWN M.HALASZ CHECKED J.MCFADGEN DATE 2016-03-08 W.O. XXXX NSPI APPROVAL: Jimtalya POWER DEMER COMPANY CHECKED J.MCFADGEN DATE 2016-03-08 W.O. XXXX...
AI summary The text references Clause 12.7 (D) of the Utility Services Requirements Book and includes a table with information related to NSPI (Nova Scotia Power Inc.), including approvals, service entrance configurations, and a drawing reference. A figure is also mentioned.
- 1.) THE MINIMUM DISTANCE FROM THE CORNER OF THE STRUCTURE TO THE TIP OF THE SERVICE ENTRANCE FITTING MUST BE 150mm. - 2.) IF THERE WILL BE A DOWN SPOUT FOR A RAIN WATER COLLECTION SYSTEM ON THE SAME CORNER AS THE SERVICE, THEN THE DISTAN...
AI summary The text outlines specific installation requirements for service entrance fittings, including minimum distances from building corners, adjustments for rainwater downspouts, and measurement guidelines for supply cable attachment points.
MINIMUM CLEARANCES UNDER ROADWAYS/DRIVEWAYS DATE: 2008-09-15 REV DATE: 2016-04-11 DRAWN: H. V. HUYNH STD NO: 1U-ED-44M APPROVED: Juntalyan SHEET: 1 of 1 ( R1 ) MINIMUM CLEARANCES BETWEEN POWER DUCTS AND SWIMMING POOLS
AI summary This document outlines the minimum clearances required between power ducts and swimming pools under roadways and driveways, as specified in standard 1U-ED-44M, last revised on April 11, 2016.
TABLE I VOLTAGE (B) COLUMN A COLUMN B 0 - 750 V 750 1500 750 V - 15 kV 1500 3000 15 kV - 22 kV 2000 4000 NOTES:
AI summary The document contains a table outlining voltage ranges and corresponding values for columns A and B, likely related to electrical distribution or grid planning. No specific arguments or entities are discussed in the text provided.
- A . REFER TO DWG. NO. IJ-ED-44M FOR ROADWAY/DRIVEWAY REQUIREMENTS . MAY BE REDUCED TO 600 mm IF VOLTAGE DOES NOT EXCEED 750 VOLTS PHASE TO PHASE . - B . VOLTAGES ARE RMS PHASE TO GROUND . - C . NATIVE BACKFILL MATERIAL SHALL NOT CONTAIN...
AI summary The text outlines technical specifications for electrical installations, including roadway/drveway requirements, voltage standards, backfill material restrictions, compaction requirements, and unit of measurement. These specifications are part of a standards committee-approved document.
URD BOX AND CONDUIT DETAILS SHOWING SECONDARY AND CUSTOMER'S CONDUITS FOR SINGLE FAMILY HOMES DATE: 1988-08-15 REV DATE: 20 18-10 -09 DRAWN: P. HUBLEY STD NO: 21 J-EC ) - 30N / APPROVED: gist-today SHT NO: 1 OF 1 (R2) // V
AI summary This document provides technical details regarding URD box and conduit configurations for secondary and customer conduits in single-family homes, dated August 15, 1988, with revisions noted.
URD BOX AND CONDUIT DETAILS SHOWING THROUGH SECONDARY AND CUSTOMER SERVICE FOR CONDOMINIUMS DRAWN: P. HUBLEY STD NO: 2U-ED-36M APPROVED: SHT NO: 1 OF 1 (R2) DATE: 1988-08-15 REV DATE: 20 18-10 0-09 APPROVED: 0:1 OF 1 (R2 DRAWN: P. HUBLEY S...
AI summary This document provides technical details related to URD box and conduit installations for condominiums, including drawing information, standard numbers, and revision dates. It is a technical drawing with limited textual content.
URD BOX AND CONDUIT DETAILS SHOWING SECONDARY AND CUSTOMER SERVICE FOR CONDOMINIUMS DATE: 1988-08-15 REV DATE: 20 18-10 0-09 DRAWN: P. HUBLEY STD NO: 2 U–EC 18E– Λ APPROVED: gintedy- SHT NO: 1 OF 1 (R2)
AI summary This document contains technical details related to URD box and conduit installations for secondary and customer service in condominiums, dated August 15, 1988, with revisions noted.
ABOVE GROUND URD BOX AND CONDUIT INSTALLATION DETAILS DATE: 2013-10-28 REV DATE: 20 18-11 -07 DRAWN: P. HUBLEY STD NO: 2 U–ED ) - 54N Л APPROVED: and the SHT NO: 1 OF 1 (R2) (/ 0 VOLTAGE RATING OF TRANSFORMER (V) TX RATING (KVA) 600 Y / 34...
AI summary The document provides installation details for above ground URD boxes and conduits, including transformer voltage ratings and the number of acceptable cable connections for different transformer capacities.
MAXIMUM NUMBER OF SECONDARY CABLES ON 3 PHASE PADMOUNTS DATE: 2016-01-06 REV DATE: 20 16-04- 12 DRAWN: PAUL HUBLEY STD NO: 41 U–7M APPROVED: Jintong- SHT NO: 1 OF 1 (R1)
AI summary This document outlines technical specifications for the maximum number of secondary cables on 3 phase padmounts, with details including date, revision date, and approval information.
REINFORCING DETAILS FOR CONCRETE PAD SINGLE - PHASE PADMOUNT TRANSFORMER 50kVA - 167kVA DATE: 2008-09-15 REV DATE: 20 17-02 -03 DRAWN: P. HUBLEY STD NO: 6 U–ED -11N 1 APPROVED: Ji-Tily- SHT NO: 1 OF 1 (R2)
AI summary This document provides reinforcing details for a single-phase padmount transformer with capacities ranging from 50kVA to 167kVA, including a drawing date of September 15, 2008, and various revision and standard numbers.
FIRE-RESISTING BARRIER FOR SINGLE-PHASE PADMOUNT TRANSFORMER 50 kVA - 167 kVA DATE: 2008-09-15 REV DATE: 2016-04-11 DRAWN: H. V. HUYNH STD NO: 6U-ED-12M APPROVED: Jintu Fadya SHEET: 1 of 1 (R1) CONCRETE TOP OF FIRE-RESISTING BARRIER SINGLE...
AI summary This document provides technical specifications for a fire-resisting barrier for single-phase padmount transformers ranging from 50 kVA to 167 kVA, including details on the concrete top of the barrier, drawing number, and revision date.
CONCRETE PAD FOR THREE-PHASE PADMOUNT TRANSFORMER 750KVA - 2500kVA (DEEP-WELL DESIGN) DATE: 2008-08-14 REV DATE: 2017-02-15 DRAWN: H.V. HUYNH STD NO: 6 6U-ED-26M APPROVED: Jim Troy SHT NO: 1 OF 1 (R1)
AI summary This document provides technical specifications for a concrete pad designed for a three-phase padmount transformer with capacities ranging from 750KVA to 2500KVA, specifically for a deep-well design. It includes details such as the date, revision date, drawing number, and approval information.
FIRE-RESISTING BARRIER FOR THREE-PHASE PADMOUNT TRANSFORMER 750 kVA - 2500 kVA DATE: 2008-08-14 REV DATE: 2016-04-12 DRAWN: H. V. HUYNH STD NO: 6U-ED-28M APPROVED: girthe Fadyan SHEET: 1 of 1 (R1)
AI summary This document outlines the specifications for a fire-resisting barrier for a three-phase padmount transformer with capacities ranging from 750 kVA to 2500 kVA. It includes a drawing date, revision date, standard number, and sheet information, as well as a reference to a figure.
TYPICAL CONSTRUCTION DETAILS OF FIRE-RESISTING BARRIERS FOR PADMOUNT TRANSFORMERS DATE: 2008-09-15 REV DATE: 2016-04-12 DRAWN: H. V. HUYNH STD NO: 6U-ED-38M APPROVED: Jinta Frogan SHEET: 1 of 1 (R1)
AI summary This document provides construction details for fire-resisting barriers for padmount transformers, including a drawing date, revision date, and standard number. It is part of a technical specification related to electrical infrastructure.
TRANSFORMER PAD PROTECTION AGAINST VEHICULAR TRAFFIC DATE: 2008-09-15 REV DATE: 2016-04-12 DRAWN: H. V. HUYNH STD NO: 6U-ED-40M APPROVE D: Jinhitadyan SHEET: 1 of 1 (R1) IN PADMOUNT TRANSFORMER TO CUSTOMER SERVICES FOR SINGLE FAMILY HOMES
AI summary This document outlines the design and approval process for transformer pad protection against vehicular traffic, specifically for padmount transformers serving single-family homes. It includes technical details and revision dates.
INSTALLATION DETAILS FOR SINGLE PHASE ABOVE GROUND MV JUNCTION BOX DATE: 2015-07-09 REV DATE: 2016-04-12 DRAWN: H. V. HUYNH STD NO: 8U-ED-35M APPROVE D: Jinhi Fadya SHEET: 1 of 1 (R1)
AI summary This document provides installation details for a single-phase above ground MV junction box, including drawing information, revision dates, and standard number. It includes a reference to a technical drawing and is associated with Nova Scotia Power Inc.
UNDERGROUND TEMPORARY SERVICE DATE: 2008-08-14 REV DATE: 2016-04-12 DRAWN: H. V. HUYNH STD NO: 8U-ED-40M APPROVED: Jintutadyan SHEET: 1 of 1 (R1)
AI summary The document provides information about an underground temporary service, including the date, revision date, drafter, standard number, and sheet details. It includes a reference to an image file.
DUCT TERMINATION AT POLE FOR UNDERGROUND PRIMARY SERVICE DATE: 2008-08-14 REV DATE: 201 6-04 -12 2 DRAWN: M. HALASZ STD NO: OU -ED-1 0M , APPROVED: J.A.MCFADGEN SHT NO: 1 OF 1 (R2)
AI summary This document is a technical drawing related to the duct termination at a pole for underground primary service, dated August 14, 2008, and revised on June 4, 2012. It includes information about the drafter, approver, and standard numbers.
TRIPLEX SERVICE CONNECTION ON SERVICE MAST 120/240V (400A OR LESS) DATE: 2008-08-14 REV DATE: 202 2-02 -16 õ DRAWN: M. HALASZ STD NO: SS- ED-13 M APPROVED: J.A.MCFADGEN SHT NO: 1 OF 1 (R4)
AI summary The document is a technical drawing related to a triplex service connection on a service mast for 120/240V (400A or less), dated August 14, 2008, with revisions and approvals noted.
TRIPLEX SERVICE CONNECTIONS FOR EXISTING SINGLE DWELLINGS 120/240V (400A OR LESS) DATE: 2008-08-14 REV DATE: 2023-03-20 DRAWN: M.HALASZ STD NO: SS-ED-14M APPROVED: J.A.MCFADGEN SHT NO: 1 OF 1
AI summary This document provides technical specifications for triplex service connections for existing single dwellings operating at 120/240V with a maximum capacity of 400A. It includes a revision date of March 20, 2023, and is part of a standardized engineering document.
TEMPORARY SERVICE STRUCTURE WITH PLANKS SURFACE MOUNT 120/240 VOLTS (200 AMPS OR LESS) PLAN, ELEVATIONS, MATERIAL LIST DATE: 2008-08-14 REV DATE: 2023-02-02 DRAWN: M. HAL ASZ STD NO: SS- ED-2 3MA 1 APPROVED: J.A.MCFADGEN SHT NO: 1 OF 2 (R2)
AI summary This document outlines a temporary service structure with planks surface mount for 120/240 volts (200 amps or less), including plan, elevations, and material list. It includes revision dates and drawing information.
TEMPORARY SERVICE STRUCTURE WITH PLANKS SURFACE MOUNT 120/240 VOLTS (200 AMPS OR LESS) DETAIL 'A' AND NOTES DATE: 2008-08-14 REV DATE: 2023-02-02 DRAWN: M. HAL ASZ STD NO: SS- ED-2 3MA APPROVED: J.A.MCFADGEN SHT NO: 2 OF 2 (R1)
AI summary This document provides technical specifications for a temporary service structure with planks surface mount for 120/240 volts (200 amps or less), including details and notes. It includes revision dates and information about the drawing and approval.
TRIPLEX SERVICE CONNECTION FOR MOBILE HOME 120/240V (200A OR LESS) CUSTOMER'S INSTALLATION AND WALL SUPPORT OF SERVICE MAST DATE: 2008-08-14 REV DATE: 202 22-02 -16 5 DRAWN: M.HALASZ STD NO: SS- ED-2 5M APPROVED: J.A.MCFADGEN SHT NO: 1 OF...
AI summary This document outlines the technical specifications for a triplex service connection for a mobile home with a 120/240V (200A or less) electrical system, including customer installation and wall support of the service mast. It includes a drawing dated August 14, 2008, and details related to the design and approval process.
TRIPLEX SERVICE CONNECTION DETAILS FOR LINKED HOMES DATE: 1997-11-01 REV DATE: 2022 2-02- -16 5 DRAWN: M. HALASZ STD NO: SS-E D-30 М APPROVED: J.A.MCFADGEN SHT NO: 1 OF 1 (R2)
AI summary The document provides triplex service connection details for linked homes, including a technical drawing and metadata such as dates, revision dates, and personnel involved in the approval process.
RECOMMENDED CLEARANCES TO ADJACENT STRUCTURES DATE: 2020-07-02 REV DATE: DRAWN: M. HALASZ STD NO: V-ED-13M APPROVED: Jan me fady 1. Co. SHT NO: 1 OF 2 - A. NO PERMANENT BUILDING OR STRUCTURE SHALL BE PLACED WITHIN 5000mm MEASURED RADIALLY...
AI summary The document outlines recommended clearances for structures near primary voltage conductors, specifying that no permanent building or structure should be placed within 5000mm radially from any primary voltage conductor or equipment.
APPROVED COMPRESSION TERMINALS FOR ALUMINUM CABLES DATE: 2016-01-14 REV DATE: 20 18-02 2-28 DRAWN: PAUL HUBLEY STD NO: 4 U-11. М DESIGNED: A. KOVALKO SHT NO: 1 OF 1 (R1) Compres sion Term ninals for Copper Cables 3 CABLE SIZE AWG/kc mil Ho...
AI summary The document provides a technical table outlining approved compression terminals for aluminum cables, including various cable sizes, terminal models, and associated codes. It is part of a regulatory document related to distribution standards.
APPROVED COMPRESSION TERMINALS FOR COPPER CABLES DATE: 2016-01-14 REV DATE: 20 18-02 2-28 DRAWN: PAUL HUBLEY STD NO: 4 U-12 M DESIGNED: A. KOVALKO SHT NO: 1 OF 1 (R1) APPENDIX D NPSI APPROVED UNDERGROUND MATERIALS
AI summary The document provides information on approved compression terminals for copper cables and lists underground materials approved by NPSI. It includes details such as dates, standards, and designations related to the materials.
- 2. The item numbers refer to the number shown inside a circle (or ellipse) on the drawings. ITEM NO. DESCRIPTION MFG.CAT.NO. C 1066 CONDUIT – COUPLING PVC TO PVC, FOR USE ON 4" (100 MM) DB TYPE II CONDUIT SCEPTER EC55 C l067 CONDUIT – CO...
AI summary The text lists various items with descriptions and manufacturer catalog numbers, primarily related to electrical conduit, connectors, and enclosures used in infrastructure. These items are referenced by item numbers and include details on materials and specifications.