98234Complainant Submission - Nova Scotia Power Inc. Utility Service Requirements 2023 Edition - Effective May 1, 2023
9 passages
Inspection Authority: The Nova Scotia Department of Labour and Advanced Education have responsibility for enforcement of the Electrical Requirements in the Province of Nova Scotia. Nova Scotia Power's Electrical Inspection Department is au...
AI summary The Nova Scotia Department of Labour and Advanced Education is responsible for enforcing electrical requirements in the province. Nova Scotia Power's Electrical Inspection Department enforces the Canadian Electrical Code, Part 1 and Utility Standards within its service area.
5 Requirements for Service Connection Service entrances will be connected upon compliance with the following requirements: - a) Supply Authority approval of the service entrance location, capacity and provisions for metering equipment. - b...
AI summary The document outlines seven requirements for service connection, including supply authority approval, wiring permits, utility connection authorization, compliance with electrical plans, adherence to the Canadian Electrical Code, easement requirements, and building permits where required by the municipal government.
6.1 Secondary Supply Voltages The following are standard secondary and service voltages: - a) 120/240 volt, single phase, three wire; or - b) 120/208 volt, three phase, four wire grounded wye; or - c) 347/600 volt, three phase, four wire g...
AI summary The document outlines standard secondary and service voltages for electrical supply, including 120/240, 120/208, and 347/600 volts. High resistance grounded installations require approval from the Supply Authority and must comply with the Canadian Electrical Code. Non-standard installations must be modified to meet these standards during service alterations.
9 Transfer Equipment for Standby Power Systems Transfer switches for transferring the source of power from the utility system to a standby power system must meet the requirements of CE Code 14-612. The switch shall not allow the two source...
AI summary This section outlines requirements for transfer switches used in standby power systems, emphasizing compliance with the Canadian Electrical Code and the need for utility consultation and approval for synchronized transfer switches and meter base accessories.
12.5 Prefabricated Homes As with buildings constructed on site, the Customer shall obtain approval from the Supply Authority for the route of the utility supply conductors and the location of the service entrance for prefabricated homes (m...
AI summary The document outlines requirements for obtaining approval from the Supply Authority for the route of utility supply conductors and the location of the service entrance for prefabricated homes, such as modular and mini homes, constructed on specific building lots.
12.7 Services to Sheds, Recreational Vehicles, and Small Structures Services for recreational vehicles shall be considered permanent regarding the requirements of the Canadian Electrical Code, Part 1. This type of service must be installed...
AI summary The document outlines requirements for electrical services to recreational vehicles and small structures, emphasizing the need for permanent installations. Customers are responsible for providing acceptable structures, such as sheds or poles, that meet specific standards and are approved by the Supply Authority and Inspection Department.
13.4 Customer Responsibilities Customer is responsible for all the following at their cost: - 1) Prepare a design indicating pole locations, the position of URD boxes, and the conduit system as per NSPI requirements. - 2) The customer is r...
AI summary The section outlines the responsibilities of customers and developers in the installation and maintenance of electrical infrastructure, including design, excavation, conduit installation, and compliance with NSPI and electrical code requirements.
14.4 Duct Banks The customer shall provide a suitable underground ductbank as shown on Dwg. 1U-ED-12M and Dwg. 1U-ED-14M. If telephone ducts are not required, they may be eliminated along with the wooden plank separation. Drawing 5U-ED-10M...
AI summary This section outlines the specifications for duct banks, including material approvals, installation requirements, and safety distances from other underground systems. It emphasizes compliance with certification standards, duct sizing, and separation requirements to ensure safe and effective installation.
CUSTOMER MATERIAL - 1 FACE MINIMUM 4'-0"x 2'-0"x 3/4" PLYWOOD OR BOARDS - 2 FRAMING 2"X 4" LUMBER - 3 BASE MINIMUM 4'-0"x 2'-0"x 3/4" (SAME AS FACE) - 4 10' GROUND ROD OR GROUND PLATE - 5 SQUARE METER SOCKET - 6 WEATHERPROOF SERVICE ENTRAN...
AI summary The text outlines specific material requirements and installation standards for electrical services, including dimensions for plywood, lumber, and conduit, as well as safety and code compliance requirements. It specifies weight and height requirements for installation and compliance with the Canadian Electrical Code.